Stage lighting truss is a more common truss in the market, it not only has a wide span of erection but also withstands a lot of strength, is well transported and stored, well installed and fixed, and can be used both indoors and outdoors. stage lighting truss is more cost effective because it does not require square head connection.
What is the role of stage lighting truss base?
Square tube stage lighting truss and round tube stage lighting truss advantage comparison analysis
How to stand up the column of stage lighting truss?
The inspection of stage lighting truss carries out the whole production process, from the beginning of inspection to the process of assembly, all need to be inspected, so the aluminum truss manufacturer should implement the "three times inspection" system, improve the responsibility of each person, and more importantly, improve the ability of inspection. Here is the role of Stage lighting truss base.
Stage lighting truss base role: placed under the column Stage lighting truss, used to support the column Stage lighting truss, the base below the movable legs, can adjust the height, for the ground is not flat performance venue is very useful. stage lighting truss use with Screws connected to the top of the reverse head, surrounded by four holes inserted into the water balance bar of the diagonal support.
Stage lighting truss square sleeve is used to connect the column aluminum truss and the beam aluminum lighting frame, when tugging the square sleeve by hand, it can drive the beam up and down, there are pulleys inside the square sleeve, so that the square sleeve can slide vertically along the column direction. The square tube truss is different from the six-sided joint, which cannot move up and down after connecting the beam, but the square tube truss can be moved.
Square tube stage lighting truss is a common truss in the market, it not only has a wide span of erection but also has a high strength, can be easily transported and stored, well installed and fixed, and can be used both indoor and outdoor. The truss is more cost effective because it does not require square head connection. Shizhan Group will discuss the advantages of square tube stage lighting truss and round tube stage lighting truss.
Round tube stage lighting truss is also a widely used truss, which can be used in both indoor and outdoor areas to build showrooms or backdrops. This truss can replace the traditional aluminum lighting truss, which cannot be folded, so the capacity is also quite large, and the larger span can reach 13 meters without support. However, it should be noted that round tube fixed truss also needs to be used with square head.
Shizhan square tube truss is a sturdier type of truss, which is suitable for various occasions and can be reused, and has a large share in the market.
You can feel the service and application from Shizhan Group when you use good quality square tube truss and round tube truss in processing and production.
In the process of building stage lighting truss, stand up the column of truss is a problem that more customers consult, about the stage lighting truss overall construction parts and methods how to build invited everyone to watch this introduction.
There are two kinds of stage lighting truss columns, one is without lifting system (square set, reverse head, hoist), the overall construction of this kind of truss is quite simple, not in this explanation, the focus is on the second kind, with lifting system truss column erection method: the first method: for truss column erection, the first method is the first method.
Method 1: For truss column height not more than 8 meters and the overall weight of truss column is not too heavy, human lift can be used. As shown in the picture, after connecting the counter head, use enough manpower to lift the column. Please note that if the joist column is too heavy and the length is too high, please do not use this method.
Method 2: If the height of the truss column exceeds 8 meters or the weight of the column is large and there is no professional mechanical equipment, scaffolding or mobile aerial work platform can be used to create a high tension point to complete the erection.
Method 3: Equipped with stage lighting truss column raising frame and hand cranking turntable, the truss column can be raised by wire rope, which is simple and fast and can be done by one person. This is the majority of truss erection equipment used in truss projects.
Related Recommendations
What kind of exhibition truss is the most satisfying?
Why are Portable lighting trusses made by Shizhan so popular?
Building knowledge you need to know about after buying the stage light truss
What you need to know before and after buying a lighting truss?
What maintenance work is needed after the Stage lighting truss is built?
Top
